Landcruiser 100 / 105 Series Front Mount Intercooler Mk2 1HD series core

$1,600.00$2,320.00

or 4 fortnightly payments from $400.00 with Afterpay More info

Silver and black cores are available

The largest and most efficient intercooler for the Landcruiser 100 / 105 Series.

5.7 x bigger than factory.

The PDI Landcruiser 100 / 105 Series Front Mount Mk2 intercooler significantly raises the bar for what can be achieved. Now these engines are pumping out +300rwkw, we have the intercooler that is the clear choice for such a setup.

See below for more information.

Clear
SKU: PDI-INT-100 Category:

Description

Core size: 675x300x76. Thats over 5.8 x greater surface area than the HDJ100 factory core, is thicker and better placed for increased cooling.

Fits with all bull-bar and winch designs as the core sits back close to the condenser.

Will fit a 100 series HDj100 with no modifications to the air conditioning system. If you have a 105 and would like to fit the large core, then the hose and piping from the condenser to the compressor needs to be replaced with the recessed HDJ100 pipe, or purchase a one piece replacement from us.

Intercooler pipes: 2.5” stainless steel with heavy duty silicon joiners. Silicon selection now simplified with no silicon in front of the front panel.

High torque stainless steel clamps.

The moulded end tanks with rear facing outlets have enabled a bigger core, then we pushed it back as far as possible to increase the draw through from the engine cooling fan. With the outlets being rear facing, the stainless steel pipes are connected to the intercooler with straight silicon.

During testing we have seen this maintain intake temps to 4-7degC above ambient temperature for normal around town driving.

When under load (on the highway towing a heavy trailer) running a steady 15-18psi with 150degC the intake temps sat 15deg above ambient. On a 20degC the intake temps got up to 35deg – you’ll have to trust us, but that’s really impressive.

For HZJ105 running the 1HZ engine we suggest our smaller core (645x240x65) to reduce the heat loading on the radiator. While it is not as effective as our larger core, most 1HZ aren’t pushed too hard and this core will easily cater for almost all turbo 1HZ builds. This core is designed to fit around the condenser pipe.

Air can be felt strongly pulling through the intercooler 50-80mm in front of the core, while idling on startup. To continue to have the air being pulled through while engine temps are low (and the fan hub normally free wheels) some extra fluid can be added to the viscous coupling.

The early 100 series didn’t have any power steering cooler pipes out front and most owners leave it like that. If you have or want to maintain the power steering pipe cooler this need to be routed through the opening for the passenger side headlight.

A crossover delete option is available (extra $150) for the 1HD-FTE.

All 1HZ / 1HD-T / 1HD-FT are crossover delete design as standard and has no extra fee.

CROSSOVER DELETE OPTION

For the 1HDFTE, PDI give the option of leaving the crossover in place (with the EGR valve) or a cast alloy adapter onto the inlet manifold for all of the cruiser models (80/75/79100/105).
The 1HDFTE in our HDJ79 ute has the crossover in place and has 311rwkw and 1000nm (at the wheels). I’m sure there is a point where air flow is better without the crossover but I don’t believe we are there yet.
Leaving the crossover in place is good for:
1. Legally it has to be there since the EGR valve is in the crossover – you can still stop EGR gas flow with the valve in place.
2. No more power is made by removing the crossover (for most people)
3. Smooth shutdown is possible with the crossover and butterfly in place.
4. If the engine ever runs on its own fumes (and I’ve seen two FTEs do that) then turning off the key turns off the engine.
5. If it’s the late model with electronic butterfly then it must remain plugged in to the harness.
6. If you need to pass a pit inspection the crossover must be fitted.

AUTOMATIC TRANSMISSION COOLER

The transmission coolers available to fit with our kits are the best we could find and we give the option of two versions for the 100/105 series. The standard one is the same as is used in the 80 series kits and we get reports that transmission temps have dropped after fitting our intercooler and trans cooler. As well as the trans cooler being very good we also expect the transmission can hold the gear for longer and stay in lock-up, which reduces heat being made.

From the pictures you can see we have chosen to have them in front of the intercooler. The auto cooler bracket has six options with three different positions for either of the two transmission coolers. We recommend having them in the lower position to prevent heat transfer into the intercooler but if other items such as winches are fitted it would be good idea to have the transmission cooler lifted up for better cooling.

PLATES DIMENSIONS HEAT DISSIPATION RATING

12 plate 150mm x 585mm x 19mm   34.000BTU

13 plate 215mm x 560mm x 32mm 45,000BTU

Brand

PDI

Additional information

Weight 300 kg

Reviews

There are no reviews yet.

Be the first to review “Landcruiser 100 / 105 Series Front Mount Intercooler Mk2 1HD series core”

Your email address will not be published. Required fields are marked *

X